Type: Driver
File Name:
File Size: 3.5 MB
59 (4.61)
Downloads: 32
Supported systems: Windows XP, Windows Vista, Windows 7, Windows 7 64 bit, Windows 8, Windows 8 64 bit, Windows 10, Windows 10 64 bit
Price: Free* (*Free Registration Required)

Download Now

N9310A RF Signal Generator, 9 kHz to 3 GHz

Manual calibrations using the recommended test equipment will take approximately 45 minutes. Automating Calibration Procedures You can automate the complete verification and adjustment procedures outlined in this chapter if you have access to programmable agilent n9310a labview equipment.

You can program the instrument configurations specified for each test over the remote agilent n9310a labview. You can then enter readback verification data into a test program and compare the results to the appropriate test limit values.

pm800-m2 motherboardRelated titles
microsoft lifecam hd-6000 for notebooksShop by category
bosch ps10-2a i-driverKey Features
dell optiplex 7010 usb controllerN9310A RF Signal Generator, 9 kHz to 3 GHz
emu 1820mFrequently Bought Together

You can also enter calibration constants from agilent n9310a labview remote interface. Remote operation is similar to the local front-panel procedure. You can use a computer to perform the adjustment by first selecting the required setup.

The calibration value is sent to the function generator and then the calibration is initiated over the remote interface. The function generator must be unsecured prior to initiating the agilent n9310a labview procedure.

For further detailing on programming the function generator, see chapters 3 and 4 in the Agilent A Users Guide. Recommended Test Equipment The test equipment recommended agilent n9310a labview the performance verification and adjustment procedures is listed below. If the exact instrument is not available, use the accuracy requirements shown to select substitute calibration standards. Test Considerations Agilent n9310a labview ensure proper instrument operation, verify that you have selected the correct power line voltage prior to attempting any test procedure in this chapter.

Keysight Electronic Measurement Products Agilent

See page 22 in chapter 2 for more information. For optimum performance, all test procedures should agilent n9310a labview with the following recommendations:. Verify the function generator is set to the default power on state power on default.

A procedure is given on page Make sure that the calibration ambient temperature is stable and between 18 C and 28 C. Allow a 1-hour warm-up period before verification or adjustment. Agilent n9310a labview Verification Tests The performance verification tests use the function generators specifications listed in chapter 1, Specifications, starting on page Self-Test A series of internal verification tests that give a high confidence that the function generator is operational.

Q Quick Verification A combination of the internal self-tests and selected verification tests. P Performance Verification Tests An extensive set of tests that are recommended as an acceptance test when you first receive the agilent n9310a labview generator or after performing adjustments. O Optional Verification Tests Tests not performed with every calibration. These agilent n9310a labview can can be used to verify additional instrument specifications following repairs to specific circuits.

Self-Test A brief power-on self-test occurs automatically whenever you turn on the function generator. This limited test assures that the function generator is capable of operation.

Agilent Service Amplitude Modulation

agilent n9310a labview To perform a complete self-test hold down the Shift key as you press the Power switch to turn on the agilent n9310a labview generator; hold down the key for more than 5 seconds a complete description of these tests can be found in chapter 6. The function generator will automatically perform the complete self-test procedure when you release the key. The self-test will complete in approximately 5 seconds.Drivers>>Agilent Technologies / Keysight Technologies NA LabVIEW LabWindows/CVI Measurement Studio for Visual Studio, IVI, USB, None, Yes, Download agn, a LabVIEW USB Plug and Play (project-style) instrument driver for a RF Signal Generator from agilent.

Related Posts

Leave a Reply

Your email address will not be published. Required fields are marked *